CSVTU Question Papers for Ist Year – Engineering Graphics– Nov-Dec 2007

CSVTU Exams Papers – Ist Year – Engineering Graphics– Nov-Dec 2007:

BE (1st Semester)

Examination Nov-Dec 2007

Engineering Graphics

Q1 (a) What is representative fraction?

(b) The representative fraction of a scale showing miles, furlongs and chains is  1   / 50688  Draw a scale to read to read up to 5 lines and show on it the length representing 3 miles 5 furlongs 3 chains


An area of 144 square centimeter on a map represents an are; 36 square km on the field. Find the representative fraction c the scale of this map to measure up to 10 kilometers Indicators on this scale a distance of 7 kilo meters, 5 hectometers  and 61 decameters.

Solve any one

(c) A circle; of 50 mm diameter rolls on the circumference of another circle of 175 mm diameter outside, it. Trace the locus of a point on the circumference of rolling circle for one  compete revaluation. Draw tangent and a normal to the at a point 125 mm from the centre of directing circle.

(d) Inseribe an ellipse in a parallelogram having sides  mm and 100 m long, and an included angle of 120CJ Describe first angle projection method.

Q2 (a) Describe first angle projection method.

Solve any one

(b) Draw the projections of following points on the sarnie bar line keeping projections 25 mm apart.

(i) Point a, in the H.P. and 20 mm behind the V.P.

(ii)Point B, 15 mm above H.P. and 50 mm behind V.P.

(iii) Point C, 40 mm above the H.P. and 25 mm in front of VP. j

(iv)Point D, in the V.P. and 40 mm above the H.P

(c)  Draw the projection of a line AB when its and A is 2C the H.P. and 10mm in front of V.P. its end B is 55 the H.P. and 80mm infront of the V.P. and the distance  between the projections A and B.(measured parallel to the X-Y line) is 45 mm.Find the true length. theta and  phi  of the its traces.

(d) a line AB 65 mm long is inclined to H.P. at an angle of45° Its end point. A is 15 mm above the H.P. and 25 mm in front of  V.P. line AB is contained by a vertical plane making an angle  45°to the V.P. Draw the projections of the line.find the  inclination of the line with V.P. and locate its traces.

Q3 (a) Define autxiliary planes and classify.

(b)     A cone, base 70 mm and axis length 80 mm is kept on H.P its bar, It is cut by an AIP in such away that the true  shape of the  section is a hyper bola of base 50 mm and altitude 60 mm. Draw front view, sectional top view and true shape of the section.


A cone, base diameter 70 mm and axis length 8Cl mm is kept on the H.P. on its base. It is cut by a section plane perpendicular to both H.P. and V.P. in such a way that the true shape of the section is hyperbola of attitude 50 mm. Draw front view, top view and true shape of the section.

(c) The base surface of a stand is a square of 90 cm  sidesand is on ground. The top surface of it is a circle of 30 cm diameter  and is 70 cm above the ground. The lower ends of four legs which are equal in length and equally spaced in plan, and art connected to the corners of square in base while the top ends are on the circumference of the circle at top ends are on the circle at top


Draw the projections of the stand when the four legs are equally inclined to front wall and find the length of legs and their inclination with ground.

Q4(a) Draw the development of lateral surface of a pentagonal prism with edge of base 40 mm and height 90 mm, kept on H.P. on its base with an edge of base parallel to V.P. when it is cut by an AIP, inclined at 30°to H.P. and bisecting the axis of prism. Draw isometric view of the casting shown in two views in following figure.

Draw the isometric view of the frustum of the hexagonal pyramid having side 40 mm and axis 90 mm long and its base is on the ground as shown I following figure

Q5 (a) What are the reasons for implementing  a CAD system? Discuss the various benefits of CAD.

(b) What is Auto CAD? Discuss the functions commands of Auto CAD.

(i) MOVE                                  (ii)EXTRUDE

(iii)STYRETCH                  (iv)EXTEND


(a) Discuss the various applications and limitations of CAD?

(b) Explain various methods for drawing a circle using CIRCLE command in Auto CAD.

(c) Classify the UTILITY commands.

Leave a Comment